HP FUEL PUMPS
P/N 12-125 and 12-150
Installation Instructions
WARNING! THESE INSTRUCTIONS MUST BE READ AND FULLY UNDERSTOOD BEFORE BEGINNING INSTALLATION. FAILURE TO
FOLLOW THESE INSTRUCTIONS MAY RESULT IN POOR PERFORMANCE, VEHICLE DAMAGE, PERSONAL INJURY, OR
DEATH. IF THESE INSTRUCTIONS ARE NOT FULLY UNDERSTOOD, INSTALLATION SHOULD NOT BE ATTEMPTED.
PLEASE CONSULT HOLLEY TECH SERVICE OR A QUALIFIED MECHANIC.
APPLICATIONS:
P/N
DESCRIPTION
FLOWS
PRESSURE
REGULATOR
Built In
ALCOHOL/METHANOL
COMPATIBLE
Yes
PRESET
PRESSURE
7 PSI max
SAFETY SWITCH
SHUT-OFF
Recommended
(P/N 12-810)
Billet Aluminum Pump. One
3/8” NPT Inlet, One 3/8”
NPT Outlet
125 GPH
Free Flow
12-125
Billet Aluminum Pump. One
3/8” NPT Inlet, One 3/8”
NPT Outlet
150 GPH
Free Flow
12-803 included
Yes
17 PSI max
Recommended
(P/N 12-810)
12-150
INTRODUCTION:
Congratulations on your purchase of the Holley HP fuel pump. This instruction sheet contains all the information needed to install this fuel
pump. Please read all the WARNINGS and NOTES. They contain valuable information that can save you time and money. Holley Performance
Products cannot and will not be responsible for any alleged or actual engine or other damage, or other conditions resulting from misapplication
of the HP fuel pumps and fuel pressure regulators described herein. However, it is our intent to provide the best possible products for our
customer; products that perform properly and satisfy your expectations. Should you need information or parts assistance, please contact our
Technical Service Dept. at 1-270-781-9741, Monday through Friday, 7 a.m. to 5 p.m. Central Time. Please have the part number of the product
you purchased when you call.
NOTE: A top quality fuel filter at 70 micron or less, fuel hose and clamps, 12 gauge wire, fuel fittings, assorted terminals, a relay, and an
optional safety shut-off switch is required to complete the installation of the HP fuel pump. These parts are not included with the HP
fuel pump.
NOTE: The 12-150 HP fuel pump requires the use of a fuel pressure regulator. Holley P/N 12-803 is included for this reason.
NOTE: For optimum performance and precise fuel control, Holley ALWAYS RECOMMENDS using a Fuel Pressure Regulator.
SPECIAL CONSIDERATIONS FOR PUMPS SUBJECTED TO HIGH TEMPERATURES:
In applications where the fuel pump is subjected to high temperatures due to climate, towing, close proximity of exhaust components, high
under-car temperatures, etc., Holley highly recommends the use of a bypass style regulator (such as Holley PN 12-803BP) to eliminate potential
vapor lock issues that may occur due to the sensitivity of new fuels. If you are experiencing fluctuations in pressure readings or no-flow
conditions when temperatures rise, you will need to install a bypass regulator.
PUMP MOUNTING AND INSTALLATION:
The best location for mounting any electric fuel pump is the rear of the vehicle, near the fuel tank and in a position that will allow the fuel to be
gravity fed to the pump. The pump should be mounted on a solid member, such as the chassis, in a vertical position with the pump motor on
top. Avoid exposure of the pump and fuel lines to moving parts and to any hot areas, such as the exhaust manifold. The pump should not be
mounted in an enclosed area, such as the vehicle’s trunk. Follow the steps below for mounting the pump.
WARNING! THE PUMP MUST BE PLACED WHERE INTERFERENCE BETWEEN THE VEHICLE’S BODY AND ITS CHASSIS MOVEMENT IS
AVOIDED. THE PUMP AND ITS CONNECTING HOSES MUST NOT BE SUBJECTED TO LOW GROUND CLEARANCE, WHERE
ANY FLYING ROCKS OR ROAD DEBRIS CAN CAUSE DAMAGE. FAILURE TO AVOID THESE HAZARDS WILL LEAD TO
PUMP DAMAGE, WHICH COULD RESULT IN FIRE AND/OR PROPERTY DAMAGE, SERIOUS INJURY, AND/OR DEATH.
1. Select a mounting site as close as possible to the fuel supply and away from possible sources of heat as detailed previously.
2. Use the mounting bracket attached to the pump as a template and drill two clearance holes for 5/16” bolts.
3. Mount the pump in the vertical position (motor on top) using two 5/16 bolts.
NOTE: To ensure pump life and flow efficiency, a quality fuel filter, such as Holley P/N 162-515 must be installed between the tank and each
pump inlet. The filter should be supported in such a manner that it does not hang from the fuel lines.
WIRING:
There are 2 methods to wire the pump: (1) To wire the fuel pump with a relay (2) To wire the fuel pump with an oil pressure safety switch.
(1) WIRING THE FUEL PUMP WITH A RELAY:
NOTE: You will need Holley Fuel pump relay kit P/N 12-753 or equivalent 4-wire relay.
1. Disconnect the cables from the battery.
2. Mount relay on firewall of engine compartment using a sheet metal screw.
WARNING!
Before punching or drilling a hole in the firewall, make sure you know what is on the other side to avoid puncturing
equipment such as heater cores, air-conditioning system equipment, hoses, or wiring.
3. Plug the fuel pump relay harness into the relay, until it locks into place.
4. Connect the black wire of the harness to ground using 12 gauge wire.
5. Connect the Green/Black wire to a switched 12V source.
6. Connect one of the red wires to the positive wire (red wire) of the fuel pump.
7. Attach the in-line fuse holder to the remaining red wire. After attaching the fuse holder, insert the 15A fuse and connect to the positive side
of the battery using 12 gauge wire.
8. Reconnect the battery cables.
Figure 2
(2) WIRING THE FUEL PUMP WITH AN OIL PRESSURE SAFETY SWITCH:
One method is to wire the pump to a switched 12-volt source (providing power only when the engine is running) located at the vehicle’s electric
panel. To ensure this condition, the installation of a Holley 12-810 oil pressure safety switch is recommended for installation into the wiring
circuit. This will ensure that the pump will not continue to operate after the engine is shut off and/or when the key is left in the “ON” position. If
the pressure switch is to be used, follow the installation instructions as outlined below (refer to Figure 3). Use 12 gauge wire for power (BAT+)
and ground wires.
1. Disconnect the ground cable from the battery.
2. Remove the original equipment oil pressure switch and retain.
3. Screw a 1/8” pipe nipple into the hole from which the original pressure switch was removed. Use any suitable thread sealant on all fittings,
taking care to avoid any excess that might contaminate the engine.
4. Screw a 1/8” pipe tee onto the nipple and position it in a manner to facilitate the installation of the original oil pressure switch and the new
oil pressure safety switch in the remaining two holes.
5. Screw in the two switches and reconnect the lead to the original equipment oil pressure switch.
NOTE: The pump oil pressure switch will normally have three terminals marked: C (common), NC (normally closed), and NO (normally open).
3
Figure 3
6. Connect the fuel pump (red lead) to the terminal marked “C”. In this line, add an in-line fuse holder and a 15-amp fuse.
7. Connect the terminal marked “NO” to the on terminal of the ignition switch.
8. Connect the terminal marked “NC” to the starter terminal that’s hot (12V) during cranking only.
9. To complete the installation, connect the ground cable to the battery.
WARNING! USE A MINIMUM OF 12/14 GAUGE WIRE. BE SURE TO CRIMP ALL CONNECTORS SECURELY AND CLEAN ANY AREA
WHERE GROUND LEADS WILL BE FASTENED. FAILURE TO USE THE MINIMUM WIRE GAUGE COULD RESULT IN A
PUMP MALFUNCTION AND/OR ELECTRICAL FIRE, RESULTING IN PROPERTY DAMAGE, SERIOUS INJURY, AND/OR
DEATH.
MAINTENANCE AND CLEANING INSTRUCTIONS FOR HP PUMPS:
Due to the current poor quality gasoline that’s available, it is recommended that periodically a can of dry gas (such as STP water remover) be
used to absorb the water out of the fuel delivery system. The fuel filter element should be blown clean with compressed air every 6,000 miles
and replaced every 12,000 miles to assure maximum protections. If your fuel pump fails to pump or fails to maintain adequate pressure, check
the following:
1. Check the voltage at the pump to assure a 12 volt supply.
2. Check the fuel line (especially the fuel filter) for any obstruction. Use compressed air to blow the line free.
3. If this doesn’t solve the problem, turn the pump on and listen for a hum from the top of the pump. If there is no hum, the pump electrical
system should be checked by a competent repairman. If the pump hums, it probably only needs to be cleaned. See Figure 4.
CLEANING THE PUMP:
The following is a step-by-step procedure for cleaning the Holley electric fuel pumps. Do all disassembling on a clean bench. Read all
instructions thoroughly and completely before starting.
1. Remove the pump from the car.
2. Remove the inlet and outlet line fittings from the pump housing assembly.
3. Remove the filter screen from the inlet port and clean thoroughly with a spray-type carburetor cleaner.
4
Figure 4
4. Turn the pump upside down, remove the three bolts, and carefully lift off the pump cover followed by the gasket, pump plate, and O-Ring.
5. Very carefully remove the gerotor assembly (both parts) from the pump housing.
WARNING! KEEP THE GEROTOR TOGETHER AS A MATCHED SET. THIS ASSEMBLY MUST BE REASSEMBLED THE SAME WAY IT
WAS DISASSEMBLED. THE TOP OF EACH PART MUST REMAIN TOWARD THE TOP OF THE PUMP.
WARNING! DO NOT IMMERSE THE ENTIRE UNIT IN ANY LIQUID. IMMERSION COULD DAMAGE THE ELECTRICAL CIRCUITRY,
RESULTING IN A PUMP MALFUNCTION. A PUMP MALFUNCTION COULD RESULT IN A FIRE, WHICH MAY RESULT IN
PROPERTY DAMAGE, SERIOUS INJURY, OR DEATH.
6. Remove the relief valve plug along with the O-Ring and shim. Not all pumps use a shim. Then remove the spring and relief valve piston.
7. Do not remove the motor assembly from the pump housing assembly. If the pump seal is leaking, please call Holley Tech Service at 270-
781-9741 for assistance.
8. Clean the housing assembly, pump plate, and pump cover assembly with any good quality spray-type carburetor cleaner. Make sure the
gasket surfaces are clean. Blow parts dry with compressed air. Clean any loose Teflon sealant, etc. from the inlet and outlet ports.
9. Inspect the gerotor assembly and its corresponding contact surfaces for damage such as pits, gouges, or deep scratches. Damage and
wear of this nature can greatly affect the pump’s performance. Suspect components should be replaced.
10. Reassemble the pump in reverse order of the disassembly. Lubricate all friction surfaces during the assembly with WD-40 or equivalent.
11. Insert the relief valve piston into the pump cover assembly. The rubber end goes in first, followed by the spring. Replace the relief valve
plug with the O-Ring, making sure to replace the small brass shim on the end, if used on your pump.
12. Turn the pump housing over and insert the gerotor assembly. Keep the same sides up.
WARNING! MAKE SURE THE GEROTOR ASSEMBLY IS REPLACED IN THE SAME ORIENTATION AS WHEN IT WAS DISASSEMBLED.
KEEP THE SAME SIDES UP.
13. Set the large O-Ring in place on the pump housing along with the pump plate, gasket, and pump cover assembly. These parts can only be
positioned one way in order for the bolt holes to align. Apply a drop of Loctite to each screw. Insert the bolts and tighten to 50-60 in./lbs. of
torque.
WARNING! OVERTIGHTENING CAN CAUSE THE PUMP BASE TO CRACK ALLOWING FUEL TO LEAK. A FUEL LEAK CAN CAUSE A
FIRE AND/OR EXPLOSION, RESULTING IN PROPERTY DAMAGE, SERIOUS INJURY, AND/OR DEATH.
14. Replace the inlet filter screens along with the fuel fittings. Teflon paste can be used on the fittings and they should be torqued to 15 ft./lbs.
See the warning above.
WARNING! DO NOT USE TEFLON TAPE ON PUMP FITTINGS. THIS TAPE CAN BREAK DOWN WHEN IT COMES IN CONTACT WITH
FUEL. THE TEFLON TAPE MAY PLUG THE FUEL PUMP, CAUSING DAMAGE TO THE PUMP AND THE FUEL SYSTEM.
15. Reinstall the pump in the vehicle.
5
CLEANING THE REGULATOR:
1. Loosen the hex nut on the top of the regulator and back the adjusting screw out all the
way to relieve tension on the diaphragm spring. See Figure 5.
2. Remove the four screws holding the regulator cover on. The diaphragm and spring
will fall out.
Figure 5
3. Use a spray-type carburetor cleaner to clean the cover and regulator body.
Thoroughly spray into the ports, as well as into the check ball seat area while
depressing the check ball.
WARNING! THE BRASS SEAT ASSEMBLY IS PRESSED IN AND SHOULD NOT BE
REMOVED.
4. Blow the cover and body dry with compressed air and reassemble following the
diagram.
5. Be sure to readjust the fuel pressure with the adjusting screw after installing in your
vehicle. Pressure adjustments must be made with the engine running.
SERVICE PARTS AND ACCESSORIES:
ITEM
PART NUMBER
12-814
Chevy Small Block Mechanical Pump Block-Off Plate
Chevy Big Block Mechanical Pump Block-Off Plate
0-15 PSI Fuel Pressure Gauge (non-liquid filled) 1-1/2” Dia. 1/8” NPT
0-30 PSI Fuel Pressure Gauge (non-liquid filled) 1-1/2” Dia. 1/8” NPT
0-15 PSI Electric Fuel Pressure Gauge (dash mount)
0-15 PSI Fuel Pressure Gauge (liquid filled) 1-1/2” Dia. 1/8” NPT
0-30 PSI Fuel Pressure Gauge (liquid filled) 1-1/2” Dia. 1/8” NPT
90° Elbow for Attachment to Holley Fuel Line
Safety Shut Off Switch
12-813
26-500
26-502
26-503
26-504
26-505
26-69
12-810
Holley Performance Products
Technical Support
Toll-Free Phone: 1-866-GOHOLLEY
Phone: 1-270-781-9741
Fax: 1-270-781-9772
199R10367
Date: 12-12-06
6
|